The System Sensor D4240 4-wire photoelectric duct smoke detector features a pivoting housing that fits both square and rectangular footprints and mounts to round or rectangular ductwork. Also, this unit operates in airflow speeds of 100 to 4,000 feet per minute, temperatures of –4°F...

Johnson Controls J5351R Intelligent Addressable Heat Detector 135F Flashscan RoR

SYSTEM SENSOR M400KA CONVENTIONAL MANUAL CALLPOINT

Monitor and control modules can be used to supervise and activate sounders, strobes, door closers, pull stations, waterflow switches, conventional smoke detectors, and more. Each module is rigorously designed and tested for electromagnetic compatibility and environmental reliability, in many cases exceeding industry standards.

The Edwards SIGA-CC2A Module Class A Dual is only compatible with EST3.  The SIGA-CC2A Dual Input Signal Module is an analog addressable device use to connect a supervise Class A or Class B output circuit to two input circuits. The CC2A does not provide...

Edwards EST SIGA-CT1 Single Input Module is an intelligent analog addressable device used to connect a Class B normally-open Alarm, Supervisory, or Monitor type dry contact Initiating Device Circuit (IDC); 

FCI ATD-RL Heat Detector Head for Fire Alarm System

SIGA-IO and MIO Input/Output Modules are intelligent analog addressable devices that form part of GE Security’s Signature line of products. The actual operation of the SIGA-IO and MIO is determined by the “personality code” selected by the installer, which is downloaded to the module from...

Johnson Controls LCM-320 Loop Control Card

The FSP-951 Series detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detector’s address to be set with rotary, decimal address switches, providing exact detector location for selective maintenance...

FZM-1(A) is a standard-sized module that monitors and supervises compatible two-wire, 24 volt, smoke detectors on a Style D (Class A) or Style B (Class B) circuit. The FZM-1(A) Interface Module is intended for use in intelligent, addressable systems, where the individual address of...

The LCM-320 Loop Control Module and the LEM-320 Loop Expander Module provide NOTIFIER’s ONYX® Series of Fire Alarm Control Panels (FACPs) with Signaling Line Circuits (SLCs). The ONYX® Series NFS-640/NFS2-640 supports one LEM-320; the NFS-3030/NFS2-3030 supports up to five LCM-320s and five LEM-320s. The...

Notifier FSP-851(A) Series intelligent plug-in smoke detectors with integral communication provide features that surpass conventional detectors. Detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detector’s address to be...

The microprocessor-controlled, self-diagnostic circuitry contained in the Siemens photoelectric (conventional) smoke detector, Model OP121, eliminates an installer’s need of using burdensome sensitivity-test equipment. The Model OP121 auto-sensitivity feature originates from its internal, self-monitoring circuitry, providing dynamic verification of sensitivity and / or required maintenance....

The 2951TMJ Acclimate® detector is an intelligent, addressable, multi-sensing, low-profile detector designed for use with Johnson Controls Intelligent Fire Alarm Control Panels (CLIP or FlashScan® modes). The Acclimate detector uses a combination of photoelectric and thermal sensing technologies to increase immunity to false alarms....

Addressable Control Module provides Johnson Controls intelligent fire alarm control panels a circuit for Notification Appliances (horns, strobes, speakers, etc.) Addressability allows the M300CJ to be activated, either manually or through panel programming, on a select (zone or area of coverage) basis.

The Mircom MIX-2251B photoelectric smoke detector provides a unique optical sensing chamber that senses smoke produced by a wide range of combustion sources. Features• Sleek, low profile design• Detectors are equipped with a built-in analog communications module• Smoke detectors are available with photoelectric or...

The Mircom MIX-M501M monitor modules provide an interface to contact devices, such as security contacts, waterflow switches, or manual stations. Also, they are capable of Styles A and B supervised wiring to the load device. Additionally, Conventional 4-wire smoke detectors monitored through their alarm...

The Mircom MIX-M501MAP monitor module can be installed in a single gang junction box directly behind the monitored unit.  Also, The Mircom MIX-M501MAP is intended for use in intelligent, two-wire systems where the individual address of each module is selected using rotary decade switches....

The Notifier NMM-100P Addressable Monitor Module Use to monitor a single device or a zone of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally-open dry-contact devices. May also be used to monitor normally-open supervisory devices with a special supervisory...