Johnson Controls LCM-320 Loop Control Card

The FSP-951 Series detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detector’s address to be set with rotary, decimal address switches, providing exact detector location for selective maintenance...

FZM-1(A) is a standard-sized module that monitors and supervises compatible two-wire, 24 volt, smoke detectors on a Style D (Class A) or Style B (Class B) circuit. The FZM-1(A) Interface Module is intended for use in intelligent, addressable systems, where the individual address of...

The LCM-320 Loop Control Module and the LEM-320 Loop Expander Module provide NOTIFIER’s ONYX® Series of Fire Alarm Control Panels (FACPs) with Signaling Line Circuits (SLCs). The ONYX® Series NFS-640/NFS2-640 supports one LEM-320; the NFS-3030/NFS2-3030 supports up to five LCM-320s and five LEM-320s. The...

Notifier FSP-851(A) Series intelligent plug-in smoke detectors with integral communication provide features that surpass conventional detectors. Detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detector’s address to be...

The microprocessor-controlled, self-diagnostic circuitry contained in the Siemens photoelectric (conventional) smoke detector, Model OP121, eliminates an installer’s need of using burdensome sensitivity-test equipment. The Model OP121 auto-sensitivity feature originates from its internal, self-monitoring circuitry, providing dynamic verification of sensitivity and / or required maintenance....

Addressable Control Module provides Johnson Controls intelligent fire alarm control panels a circuit for Notification Appliances (horns, strobes, speakers, etc.) Addressability allows the M300CJ to be activated, either manually or through panel programming, on a select (zone or area of coverage) basis.

The Mircom MIX-2251B photoelectric smoke detector provides a unique optical sensing chamber that senses smoke produced by a wide range of combustion sources. Features• Sleek, low profile design• Detectors are equipped with a built-in analog communications module• Smoke detectors are available with photoelectric or...

The Mircom MIX-M501MAP monitor module can be installed in a single gang junction box directly behind the monitored unit.  Also, The Mircom MIX-M501MAP is intended for use in intelligent, two-wire systems where the individual address of each module is selected using rotary decade switches....

The Notifier NMM-100P Addressable Monitor Module Use to monitor a single device or a zone of four-wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally-open dry-contact devices. May also be used to monitor normally-open supervisory devices with a special supervisory...

Honeywell TC804E1030 Photo Electric CONVENTIONAL Smoke Detector

The System Sensor 1151 ionization detector uses state-of-the-art sensing chambers. Also, the System Sensor 1151 detector is design to provide open area protection and to be use with compatible UL-listed control panels only. The capability of plugging this detector into a variety of special...

The Network Communications Module (NCM) provides NOTIFIER’s NFS-640, NFS-3030, and NFS2-3030 Fire Alarm Control Panels, and NCA and NCA-2 Network Control Annunciators with a means to connect to NOTI•FIRE•NET™. Two types of NCM are available: NCM-W Notifier for connecting nodes with twistedpair wire, and...

The Annunciator Control Module-24AT contains 24 color-programmable (red/green/yellow) Active and 24 yellow Trouble LEDs, 24 momentary touch-pad switches, a System Trouble LED, an On-Line/Power LED, and a local piezo sounder with a silence/acknowledge switch for audible indication of alarm and trouble conditions. Includes instructions....

The NOTIFIER NCA-2 is a second-generation Network Control Annunciator for the NOTI•FIRE•NET network, compatible for use with ONYX® Series nodes such as the NFS2- 3030, NFS-3030, NFS-320, NFS-640 and NFS2-640 fire alarm control panels, as well as first-generation NCA Network Control Annunciators. Additionally, the...

The SK-MINIMON is an addressable monitor modules for use with the Honeywell Silent Knight fire alarm control panels (FACPs). The SKMINIMON acts as an interface to contact devices, such a waterflow switches and pull stations. The SK-MINIMON supports Class B supervised wiring to the...

The IDP-Minimon can be mounted in a single gang junction box directly behind the monitored device. Its small size and light weight allow it to be installed without rigid mounting requirements. The IDP-Minimon is a compact and light weight addressable monitor module for use...

MMF-301 is a miniature monitor module a mere 1.3" (3.302 cm) H x 2.75" (6.985 cm) W x 0.65" (1.651 cm) D that supervises a Style B (Class B) circuit of dry-contact input devices. Its compact design allows the MMF-301 to be mounted in...

The System Sensor M500M Monitor Module provides an interface to contact devices, such as security contacts, waterflow switches, or pull stations. Rotary Switch Addressing Standby Current: 400 μA max @ 24 VDC (one communication every 5 sec. with 47k EOL); 600 μA max @...

The FST-751 and Notifier FST-751R intelligent thermal detectors are used with the PCR-400 Fire Alarm Systems to measure thermal levels caused by fire and report the analog level of the thermal measurement to the control panel. Also, the use of analog information provides significant...